Three Tips for Proper Installation of a Sewage Ejector Pump
A sewer ejector pump is a necessary piece of plumbing equipment for homes that are below the main sewer line or septic tank. Without one, you risk having sewage back up into your home and possibly sewer gas seeping into it.
It works by putting the waste into a pit and then pumping it up to the sewer line through a discharge pipe. A vent is also attached to the vent to equalize pressure while pumping and allow for a way to escape the odors.
Make Sure the Pump is in the Right Place
A sewage ejector pump is a vital part of many homes. It lifts wastewater up to the level of the main sewer drain, keeping your basement or lower levels free from sewage-contaminated waste and odors. However, a faulty ejector pump can lead to home flooding and other plumbing disasters. If you’re planning on installing or replacing your sewage ejector pump this spring, it is essential that you have a professional from plumber Montgomery County that will assist you with the installation. Here are three tips to help you make sure that your sewage ejector pump is properly installed and functioning.
The first step in installing your sewage ejector pump is to find the right spot for it. Make sure that the area is large enough and clear of any obstacles, such as trees or rocks. Next, dig a hole for the pump and secure it in place by using cement. Finally, install a sump cover over the pump to keep it protected from debris and other potential hazards.
Once you’ve gotten your sewage ejector pump in place, it’s time to test it out. Begin by pouring water into the sewage pit to make sure that it is working correctly. If it isn’t, you may need to install a weep hole. A weep hole prevents air from building up in the pipe, which can prevent the sewage ejector pump from removing wastewater when it is activated.
Another important step is to make sure that the float switch on the sewage ejector pump is properly set. A float switch is the component that controls when the sewage ejector pump is turned on and off. It’s important that the float switch is in the correct position, which you can determine by looking at the instructions for your specific sewage ejector pump.
Finally, don’t forget to install a check valve in the sewage system. The check valve ensures that the sewage ejector pump can only move wastewater upward and toward the sewer line, and not back down into the pit. You can purchase a new check valve at your local hardware store for about $20, or you can hire a plumber to do it for you.
Make Sure the Pump is Powered
If your home has basement bathrooms, or if the main sewer line is below your house's plumbing, you will need a sewage ejector pump to pump against gravity and get rid of waste solids. Installing this system may seem like a daunting task, but with the proper knowledge and careful planning, it can be accomplished by any homeowner.
First, it is important to have the right tools for the job. A sewage ejector pump requires a sump basin, a pump, and a pipe to connect the two. If you are not sure that you have these, or if you are unsure of how to install them correctly, it is best to call a professional plumber.
A sewage ejector pump also requires a vent to equalize pressure while it is working, and to help to release sewer gases. The vent is usually connected to the existing vent stack or runs up through the roof. Finally, a check valve is placed between the sewage inlet and the sump basin to prevent the sewage from draining back into the pump after it has pumped out the water.
It is a good idea to plug the new sewage ejector pump into an electrical outlet and test it. This will ensure that the float switch is working properly and that it activates when the pump is needed. If the pump does not activate when it is needed, or if it keeps turning on and off repeatedly, you will need to have the float switch checked or replaced.
One final note: it is always a good idea to have a professional inspect the pump at least once a year. This will help to prevent problems and keep the pump running efficiently. Plumber Montgomery County can inspect the float switch and check for any clogs in the pump, as well as inspect the pipe to make sure it is properly connected.
A sewage ejector pump can be an invaluable part of your home's plumbing, but it is essential to have it installed and maintained properly in order to avoid costly damage to the plumbing system and the home itself. If you have any questions about sewage ejector pumps or would like to schedule an inspection, contact the experts at On Point Plumbing & Heating.
Make Sure the Pump is Connected to the Sewer Line
In most homes, waste and wastewater is directed through plumbing into the sewer line pipe that leads to your town’s main sewer or your septic tank. However, any drain lines that are located in basements must use an ejector pump to force the waste upward instead of depending on gravity. Without this, the sewage will back up into your basement and can even cause a dangerous septic leak.
The ejector pump is installed in a sump pit that is dug well below the grade of the home. The drain lines from the basement fixtures all lead to this pit and when the level of the sewage reaches a certain point, the float switch on the pump will move up and activate the system to begin pumping it up into the septic or sewer line. The float will then drop down and the pump will stop.
Typically, the pump will also include a vent to equalize pressure during the pumping process and to provide an outlet for sewer gasses. The vent may be connected to an existing vent stack on your roof or it may run through the wall of the basement.
Most sewage pumps will come with a basic alarm to let you know that the pump is working. For more peace of mind, you can upgrade to a smart alarm that will notify you via text or email if something is wrong with your septic or sewage system.
The most important step in ensuring that your sewage ejector pump is working properly is to ensure that the pit and float switch are free of any debris that could prevent them from operating. This includes hair, trash, and other debris that can block the float switch from moving up and down, keeping it from activating the pump when needed.
If you’re concerned that your sewage ejector pump might be causing problems, it is always best to contact a professional plumber. This is especially true for any projects that require the insertion of a new drain line. It’s likely that you will need a permit and some local communities have unique plumbing codes and requirements for work involving septic or sewer lines. Talking with a licensed plumber from On Point Plumbing & Heating first will give you a better idea of the specifics of the project and what permits might be required.
Make Sure the Pump is Working
Sewage ejector pumps are typically used in homes where the sewer line is higher than the basement plumbing. They sit in a sump basin that is cut into the ground below grade and can hold about 30 gallons of wastewater at a time for a typical house. Drain lines from the basement go down into the sewage pit, and when the level of wastewater reaches a certain height, a moveable float on the pump triggers it to turn on and start pushing the waste into the piping to the sewer or septic tank.
These systems can be difficult to maintain, and it’s important to make sure the sewage ejector pump is working properly on a regular basis. There are a few quick maintenance tasks that can be done to keep your sewage ejector pump working correctly.
The first step is to make sure the pump is plugged in and turned on. This can be done by either plugging the pump cord into a receptacle or turning on the breaker in the electrical panel.
Next, it’s important to make sure that the float switch is working properly. The float switch is a small metal device that is moved by the water pressure in the pump basin. If the float is stuck in place or doesn’t work, it could be causing the pump to run continuously. This can cause a buildup of waste and eventually cause the pump to stop working.
Finally, it’s important to check the vent for the sewage ejector pump on a regular basis. The vent allows air to escape from the sewage basin and prevents odors from coming into the house. A plumber will check for a clear, unobstructed vent hole and replace any damaged or missing pieces to ensure the system is functioning properly.
If you are having trouble with your sewage ejector pump, plumber Montgomery County can help! Our skilled technicians can diagnose the problem and get it fixed for you quickly. Contact us today to schedule an appointment! We offer emergency services as well, so don’t hesitate to call us if you are in need of assistance.
A sewer ejector pump is a necessary piece of plumbing equipment for homes that are below the main sewer line or septic tank. Without one, you risk having sewage back up into your home and possibly sewer gas seeping into it. It works by putting the waste into a pit and then pumping it up…